ESU > DIGITAL CONTROLLERS > SOUND DECODERS > DCC DECODERS > PRICE LIST > CATALOGUE
		The new LokPilot digital decoder by ESU is the world's smallest multi protocol decoder. The LokPilot combines the directional relays of an AC locomotive and a quality digital decoder suitable for Motorola-format and DCC-format (multi protocol). No matter if you operate on a digital layout with NMRA / DCC or Märklin Motorola or analogue with DC or AC, the decoder understands every language and works reliably. Fitted with overload protection for the motor as well as the function outputs, the decoder is extremely robust. High frequency motor control assures smooth and silent running.
The performance in DC analogue operation convinces the discerning modeler. Analogue operation has also been optimized: the decoder reliably recognizes the change of direction pulse across a large voltage range. Third generation load control provides excellent low speed properties. The most important function of a Digital decoder ismotor management. Therefore, all LokPilot decoders are universally usable and can be employed with all customary DC model railroad motors, such as Roco®, Fleischmann®, Brawa®, Mehano®, Bemo®, LGB®, Hübner®, Märklin® or others. Even coreless motors (e.g. Faulhaber® or Maxon®) can be connected. You can keep using all-current motors, if you replace the field winding with a permanent magnet.

	The Decoder-Tester (Profi-Pruefstand) is a welcome addition to your digital layouts. Equipped with all digital sockets (6-, 8- and 21- pin) with NEM 651 and NEM 652 interfaces, an LED monitor and loudspeaker, it allows you to test your decoders quickly and easily without having to install them first in your locomotives.
ESU 51900. Profi-Pruefstand Decoder-Tester. $95.75
	The LokPilot Basic supports the worldwide recognized DCC protocol. In this mode it can be utilized with 14, 28 or 128 speed steps, or on Analog DC layouts. It supports Lenz® LG 100 resp. Roco® braking sections as well as braking in DC sections with reverse polarity.You can use addresses 1 - 119. During operation, the LokPilot Basic decoder converses fully automatically between operational modes (DC, DCC). That's important in case you run parts of your layout (fiddle yard) in analog mode.
ESU 52690. LokPilot Basic. With wire harness 88mm and 8-pin DCC plug (NEM652)(HO gauge - for DCC). $52.50 ESU 52692. LokPilot Basic DCC+DC, with 21MTC connector $52.50
	The LokPilot V3.0 The LokPilot V3.0 commands DCC through 14, 28 and 128 speed steps, as well as Motorola® and Selectrix®. The decoder recognizes the speed-step numbers automatically. It supports Lenz® LG 100 resp. Roco® braking sections as well as Zimo®'s HLU-commands, or the braking in DC braking sections with reversed polarity, or the Märklin® braking section (even for DCC). You can either use two digit (1 - 127), or four digit (1 - 9999) addresses or assign a consist address. The Motorola® protocol enables the LokPilot V3.0 decoder to run with Märklin® stations 6020, 6021, Delta®, Mobile Station® and Central Station®. The decoders can command addresses 1 - 255, and come to a stop correctly on the Märklin® braking section. With Selectrix® layouts you have the choice of up to 122 addresses. The LokPilot V3.0 converts during operation fully automatically between all control modes (Motorola®, DCC, DC, AC and Selectrix®). RailCom® already ensures that the decoder will be recognized by the main track and can send its address. Connected with an ECoS command station and an ECoSDetector feedback module unprecedented possibilities of playing will be possible..
NEW! ESU 52610 LokPilot V3.0, multiprotocol decoder (MM/DCC/SX), with 8-pin plug according to NEM652 NEW! ESU 52612 LokPilot V3.0, multiprotocol decoder (MM/DCC/SX), with 6-pin plug according to NEM651 Stecker. $68.50 NEW! ESU 52614 LokPilot V3.0, multiprotocol decoder (MM/DCC/SX), with 21MTC connector. $68.50 NEW! ESU 52611 LokPilot V3.0 DCC decoder, with 8-pin plug according to NEM 652. $62.75 NEW! ESU 52613 LokPilot V3.0 DCC decoder, with 6-pin plug according to NEM 651. $62.75
	The LokPilot V.3 M4 The LokPilot V3.0 M4 was developed from scratch especially for Märklin® systems. It reflects years of experience, gathered by ESU during the engineering of digital decoders. The LokPilot V3.0 M4 is a genuine multi-protocol decoder. Besides its main field of application in combination with mfx® stations, it handles Motorola® command stations (e.g. Märklin® 6021) as well as conventional AC driven layouts. The LokPilot V3.0 M4 recognizes the operational mode fully automatically and converts on the fly.
ESU 61600. LokPilot V.3 M4 (HO gauge - for Märklin). Multiprotocol decoder, mfx/Motorola with 8-pin plug according to NEM 652. $100.00
	LokPilot micro V.3 DCC The LokPilot micro V3.0 DCC handles DCC with 14, 28 and 128 speed steps. The decoder recognizes the speed steps automatically. It supports Lenz LG 100, respectively ROCO braking sections, as well as Zimo HLU-commands, or braking in DC-sections with reversed polarity. You can either use short (1 - 127), or four digit addresses, or assign a consist address. During operation it converses fully automatically between control modes. It is prepared for the NMRA / DCC "BiDirectional Communication", and a simple upgrade will enable it to take advantage of those benefits. Especially in combination with our ECoScenter, there will be up to now, unheard-of operational possibilities, and play value in the future. DCC is available in two variants: With either a separate NEM 651 Norm 6 wire harness-plug combo, or with 6, permanently to the decoder fastened connecting pins.
NEW! ESU 52684. LokPilot micro V3.0 DCC. Decoder, with 6-pin plug according to NEM 651 with wire harness. $98.00 NEW! ESU 52685. LokPilot micro V3.0 DCC. Decoder, with 6-pin plug according to NEM 651 without wire harness. $98.00
	The LokPilot micro V.3 is a genuine power house. With its continuous load capability of 0.75 A and a size of only 13.5mm x 9.0mm x 3.5 mm ( .54 x .36 x .12 inch ) it is perfectly suited for N Scale -, or small HO Locos with limited room and high current drain. Despite many other decoders released on the market it is a real multi-protocol decoder, that speaks beside DCC also Motorola® and even Selectrix®. Handles DCC with 14, 28 and 128 speed steps as well as Motorola® and Selectrix®. The decoder recognizes the speed steps automatically. It supports Lenz® LG 100, respectively ROCO® braking sections, as well as braking in DC-sections with reversed polarity or the Märklin® braking section (also DC). You can either use short (1 - 127), - or four digit addresses, or assign a consist address. The Motorola® protocol enables the decoder to be used with Märklin® stations 6020®, 6021®, delta®, mobile station® and central station®. The LokPilot mirco V3.0 reads the addresses 01-127 and will stopp correctly on the Märklin® braking section. If used on a Selectrix® layout you can chose between address 1-112. It changes the operation mode automatically (Motorola®, Selectrix®, DC and DCC) during operation.
NEW! ESU 52687. LokPilot micro V3.0 Multi-protocol decoder(MM/DCC/SX), with 6-pin plug according to NEM 651 with wire harness. $98.00 NEW! ESU 52688. LokPilot micro V3.0 Multi-protocol decoder(MM/DCC/SX), with 6-pin plug according to NEM 651 without wire harness. $98.00
	LokPilotXL V3.0 can handle DCC with 14, 28 and 128 speed steps as well as Motorola. It supports Lenz LG100 resp. ROCO brakingsections as well as Zimo HLU-commands, or braking in DC sections with reversed polarity, or the Märklin braking section (also for DCC). You can either assign a short, or four digit address. The Motorola protocol facilitates the operation of the LokPilot XL V3.0 decoders with Märklin centers 6020, 6021, Delta, mobile station and central station. For those, the decoders can handle addresses 01 - 255 and come to a halt at the correct position on the Märklin braking section. The LokPilot XL V3.0 converses during operation fully automatically between all control modes (Motorola, DCC, DC, AC) and recognizes the speed steps automatically.
NEW! ESU 51702. LokPilotXL V3.0 multiprotocol decoder (DCC/MM), with screwing terminal. (G & 1 gauge - for DCC and Motorola). $144.25
	LokPilot Fx V3.0. Motor-less rolling stock can be digitalized with the LokPilot Fx V3.0. To this end, LokPilot Fx V3.0 offers six function outputs, which can activate typical functions, such as car interior illumination, head-or rear (- end, warning- ) lights on cars, and function models. Of course LokPilot Fx V3.0 is multi protocol capable, and with a dimension of 17.5 x 15.0 mm's (0.7 x 0.6 in) small enough for most any application. LokPilot Fx V3.0 comes in two variants: Next to the [base "]classic" version with an 8-wire NEM 652 harness, there is a version available for the new 21-pin mtcinterface.
ESU 52620. LokPilot Fx V3.0 Function decoder (MM/DCC/SX), with 8-pin plug according to NEM652. $44.25 ESU 52621. LokPilot Fx V3.0 Function decoder (MM/DCC/SX), with 21MTC connector. $44.25
	LokPilot Digital Sets. To simplify conversion of your Delta-Locos as much as possible, the LokPilot Digital Set is available. It contains a LokPilot V3.0 decoder, an appropriate permanent magnet and 2 choke coils. You do not need to buy every single item: benefit from the price advantage of the whole set.
NEW! ESU 52630 LokPilot digital set 1, with LokPilot V3.0 52610, permanent magnet 51960, choke coils. $86.00 NEW! ESU 52631 LokPilot digital set 2, with LokPilot V3.0 52610, permanent magnet 51961, choke coils. $86.00 NEW! ESU 52632 LokPilot digital set 3, with LokPilot V3.0 52610, permanent magnet 51962, choke coils. $96.75
Models shown here include current releases and new items for 2010. For specifications or more information about other ESU models or to find the catalogue number for the sound of your choice visit the ESU website. You can order these models direct from All Aboard Exclusive ON-LINE. More product details available on our Products page.